Fulltext results:

Vyatta - IPSec Brige / L2TP(IPSec)+Nat @05_network:04_vyatta

71 Hits, Last modified: 13 years ago

)+Nat ====== |Name|eth0|eth1|localPC| |vyatta-A|10.10.10.246/24|192.168.10.246/24|192.168.10.5/24| |vyatta-B|10.10.20.75/24|192.168.20.75/24|192.168.20.250/24

Vyatta Openvpn @05_network:04_vyatta

23 Hits, Last modified: 13 years ago

Openvpn ====== |Name|eth0|eth1|vtun0| |vyatta-A|10.10.10.246/24|192.168.10.246/24|172.16.100.246| |vyatta-B|10.10.20.75/24|192.168.20.75/24|172.16.100.75| <c

07 OpenVswitch ovs

18 Hits, Last modified: 3 years ago

gorithm: balance-slb bond-hash-basis: 0 updelay: 31000 ms downdelay: 200 ms next rebalance: 178216 ms ... tions: {df_default="true", in_key=flow, local_ip="10.10.10.101", out_key=flow, remote_ip="10.10.10.119"} Port patch-int Interface patch-i

Vyatta - Nat @05_network:04_vyatta

13 Hits, Last modified: 13 years ago

<code console> $ configure # set nat source rule 10 # set nat source rule 10 outbound-interface eth0 # set nat source rule 10 source address '192.168.0.0/16' # set nat source rule 10 translation address masquerade </code> ===== Desc

Vyatta Backup/Reestore @05_network:04_vyatta

11 Hits, Last modified: 13 years ago

up.config set interfaces ethernet eth0 address '10.10.100.1/24' set interfaces ethernet eth0 duplex 'auto' set interfaces ethernet eth0 hw-id '52:54:00... et interfaces loopback 'lo' set nat source rule 10 outbound-interface 'eth0' set nat source rule 1

Vyatta - L2TP(IPSec) @05_network:04_vyatta

8 Hits, Last modified: 13 years ago

報を扱う際には十分な効力を発揮します。 ===== 環境 ===== |Global側|eth0|10.10.100.1| |Local側|eth1|192.168.1.1| +----------+ +----------+ ... dns-servers { server-1 10.10.100.5 server-2 10.10.100.2

Vyatta OpenVPN Server/Client @05_network:04_vyatta

8 Hits, Last modified: 13 years ago

erver/Client ====== ===== 環境 ===== |Global側|eth0|10.10.100.1| |Local側|eth1|192.168.1.1| |仮想LAN|vtun0|172.16.100.1| +----------+

Vyatta Cluster @05_network:04_vyatta

4 Hits, Last modified: 13 years ago

yatta Primary ====== |Global|Local| |172.20.1.252|10.1.1.252| <code> set cluster dead-interval '20000... .254/24/eth0' set cluster group cluster1 service '10.1.1.254/24/eth1' set cluster interface 'eth0' set... tta Secondary ====== |Global|Local| |172.20.1.253|10.1.1.253| <code> set cluster dead-interval '20000... .254/24/eth0' set cluster group cluster1 service '10.1.1.254/24/eth1' set cluster interface 'eth0' set

Vyatta - インストール @05_network:04_vyatta

4 Hits, Last modified: 13 years ago

e console> # set interfaces ethernet eth0 address 10.10.100.1/24 # set interfaces ethernet eth1 address 192.168.100.246/24 </code> ====== システム設定 ====== <code conso

Vyatta PPTP @05_network:04_vyatta

4 Hits, Last modified: 13 years ago

ト）\\ ・GRE（47番ポート） ====== 環境 ====== |Global側|eth0|10.10.100.1| |Local側|eth1|192.168.1.1| +----------+ +----------+ ... ole> # set vpn pptp remote-access outside-address 10.10.100.1 # set vpn pptp remote-access client-ip-p

Summit Command @05_network:02_summit

2 Hits, Last modified: 13 years ago

TP Diagnostic: passed Aggregate B/W: Configured 100 % Random Early Drop: Disabled Admin state: Ena... speed sensing Link state: Active. Full-duplex 100 Mbps. Link counter: Up 3 time(s), Down 2 times(... ports [<portlist> | all | mgmt] auto off {speed [10 | 100 |1000]} duplex [half | full] </code> <code console> configure ports 1 auto off duplex full s

SSG20初期化 @05_network:01_ssg

1 Hits, Last modified: 11 years ago